收藏本站联系我们 您好,欢迎来到济南空调维修,济南空调安装,三联家电售后服务中心!

新闻中心
当前位置:首页-新闻中心 >

避免日后“麻烦”,拆机后安装空调需要怎么做?

来源:http://www.jnslshwx.com 日期:2020-08-21 发布人:admin
1、回收制冷剂 必须把空调器中的制冷剂收集到室外机中去。拆机前启动空凋器,可设定制冷状态,待压缩机运转5-10分钟,制冷状态正常后,拧下外机的液体管与气体管接口上的保帽,关闭高压管(细)的截止阀门,l分钟后管外表结露,立即关闭低压管(粗)截止阀门,同的迅速关机,拔下电源插头,用扳手拧紧保险帽,至此回收制冷剂工作完成。 也可采用室内机上的强制启动按钮开机,同的观察室内、外机是否还有其他故障。避免空调移机后带来麻烦。
1. The refrigerant in the air conditioner must be collected into the outdoor unit to recover the refrigerant. Before dismantling the machine, start the air conditioner and set the refrigeration state. After the compressor runs for 5-10 minutes and the refrigeration state is normal, screw off the protective cap on the interface between the liquid pipe and the gas pipe of the external machine, close the cut-off valve of the high-pressure pipe (fine). After 1 minute of condensation on the surface of the pipe, immediately close the low-pressure pipe (thick) stop valve, and quickly shut down the power plug, and tighten the safety cap with a wrench, So far, the recovery of refrigerant is completed. The forced start button on the indoor unit can also be used to start the machine, so as to observe whether there are other faults in the indoor and outdoor units. Avoid trouble after air conditioner moving.
2、拆室内机 制冷剂回收后,可拆卸室内机。用扳手把室内机连接锁母拧开,用准备好的密封钠子旋好护住室内机连接接头的丝纹,防止在搬运中碰坏接头丝纹;再用十字起拆下控制线。同时应做标记,避免在安装时接错。如果信号线或电源线接错,会造成外机不运转,或机器不受控制。内机挂板一般固定的比较牢固,卸起来比较困难;卸完取下挂板,置于平面水泥地再轻轻拍平、校正。
2. The indoor machine can be disassembled after the refrigerant is recovered. Use a wrench to screw off the connecting lock nut of the indoor unit, and use the prepared sealing sodium to protect the silk thread of the connection joint of the indoor unit, so as to prevent damaging the silk thread of the joint during the transportation; then remove the control line with the cross start. At the same time, it should be marked to avoid wrong connection during installation. If the signal line or power line is wrong, the external machine will not work or the machine will not be controlled. The hanging board of the internal machine is generally fixed firmly, so it is difficult to remove it; after unloading, the hanging plate is removed and placed on the flat cement ground, and then gently flattened and corrected.
济南空调清洗
3、拆卸室外机式 拧开外机连接锁母后,应用准备好的密封钠子旋好护往外机连接接头的丝纹。再用扳手松开外机底脚的固定螺丝。拆卸后放下室外机时,最好用绳索吊住,卸放的同时应注意平衡,避免振动、磕碰,并注意安全。应慢慢捋直室外空调器的接管,用准备好的四个堵头封住连接管的四个端口,防止空气中灰尘和水份进入。堵头上好,最后再用塑料袋扎好,盘好以便于搬运。
3. After the outdoor unit is disassembled and the connection lock mother of the external unit is unscrewed, the silk thread protecting the connection joint of the external unit shall be screwed with the prepared sealing sodium. Then use a wrench to loosen the fixing screw of the external machine foot. When putting down the outdoor unit after disassembly, it is better to hang it with ropes. Attention should be paid to balance, avoid vibration and collision, and pay attention to safety. The connecting pipe of outdoor air conditioner should be straightened slowly, and the four ports of the connecting pipe should be sealed with prepared four plugs to prevent dust and moisture from entering the air. The plug should be fixed, and then tied up with plastic bag and coiled for easy handling.
在空调拆完后,就要安装了,我们在安装时在预定好了的位置上定好室内机的挂板,在要注意保持水平,再将空调的管子穿好后就挂好室内的机子。载根据空调管子的长度确定好室外机的位子,室外机我们也要保证它的水平。接好高低压管后,我们就打开高压阀,然后就将低压管的锁母放松,这样做的目的是排除管路中的空气,听到有气出的声音7~10后就拧紧锁母,打开低压阀,按做好的顺序连接好电线。最后接通电源,检查管路、电线、等有无接对。
After the air conditioner is disassembled, it will be installed. During the installation, we fix the hanging board of the indoor unit at the predetermined position, pay attention to keep the level, and then hang the indoor machine after the air conditioning pipe is put through. According to the length of the air conditioning pipe, determine the position of the outdoor unit. We should also ensure the level of the outdoor unit. After connecting the high-pressure and low-pressure pipes, we open the high-pressure valve, and then loosen the lock nut of the low-pressure pipe. The purpose of this is to eliminate the air in the pipeline. After hearing the sound of air coming out, tighten the lock nut 7-10, open the low-pressure valve, and connect the wires according to the order. Finally, turn on the power supply and check whether the pipelines, wires, etc. are connected properly.

上一篇:空调移机的安装应该注意什么?
下一篇:关于空调移机我们会做哪些事项?